연구성과 5 페이지 | 포항공과대학교 친환경소재대학원

커뮤니티

연구성과

Total 143건 5 페이지

79

CSPL [CSPL] Prof. Jung-Wook Cho: Numerical modeling of oxide particle evolution during additive manufacturing In this study, oxide particle evolution during additive manufacturing was modelled to elucidate the evolution and suggest effective ways to increase oxide-dispersion strengthening. The model coupled the Kampmann and Wagner numerical model w..

작성자 최고관리자 작성일 2022-02-08
78

CSL [CSL] Prof.Youn-Bae Kang: Simultaneous Analysis of Soluble and Insoluble Oxygen Contents in Steel Specimens Using Inert Gas Fusion Infrared Absorptiometry In order to evaluate cleanliness of steel samples which contain oxygen in two different forms - chemically dissolved form and physically dispersed form in steel matrix, identification of each oxygen in the steel is important. A simple but p..

작성자 최고관리자 작성일 2022-01-13
77

CSL [CSL] Prof.Youn-Bae Kang: Phase equilibria of Al2O3–TiOx system under various oxygen partial pressure: Emphasis on stability of Al2TiO5–Ti3O5 pseudobrookite solid solution Phase equilibria of Al2O3–TiOx system were experimentally determined in a wide range of T and PO2: 1300 °C ≤T≤ 1600 °C and −16.6≤logPO2≤−8.0 (in atm). X-Ray diffraction and electron probe micro-analysis were employed to obtain equilibr..

작성자 최고관리자 작성일 2022-01-12
76

EMRL [EMRL]Prof. Kyu-Young Park: Elucidating and Mitigating High-Voltage Degradation Cascades in Cobalt-Free LiNiO2 Lithium-Ion Battery Cathodes LiNiO2 (LNO) is a promising cathode material for next-generation Li-ion batteries due to its exceptionally high capacity and cobalt-free composition that enables more sustainable and ethical large-scale manufacturing. However, its poo..

작성자 최고관리자 작성일 2021-12-20
75

PEL [PEL]Prof. Young-Seek Yoon: The comprehensive evaluation of available pilot-scale H2S abatement process in a coke-oven gas: Efficiency, economic, energy, and environmental safety (4ES) This study implemented the comprehensive evaluation of desulfurization efficiency-energy potential-economic-safety into three different processes for removing hydrogen sulfide from coke oven gas. Three different processe..

작성자 최고관리자 작성일 2021-12-20
74

PEL [PEL]Prof. Young-Seek Yoon: [PEL]Prof. Young-Seek Yoon: An integrative process of blast furnace and SOEC for hydrogen utilization: Techno-economic and environmental impact assessment This study investigates Bunsen reaction in the sulfur-iodine (SI) cycle for optimal conditions and specification of equipment in terms of the maximum HI yield and the least impurities in HIx (mixture of HI, I2 and H2O), the r..

작성자 최고관리자 작성일 2021-12-13
73

PEL [PEL]Prof. Young-Seek Yoon: An integrative process of blast furnace and SOEC for hydrogen utilization: Techno-economic and environmental impact assessment The steel sector is one of the most carbon-intensive industries, and the sustainable strategies to reduce CO2 emission on integrated mill plants are discussed continuously. By renewable H2 utilization on blast furnace (BF), it is ..

작성자 최고관리자 작성일 2021-12-08
72

ADL [ADL]Prof. Yoon-Uk Heo: Comparative study on the specimen thickness measurement using EELS and CBED methods Two thickness measurement methods using an electron energy loss spectroscopy (EELS) and 10a convergent beamelectron diffraction (CBED) were compared in an Fe-18Mn-0.7C alloy. The thin foil specimen was firstly tilted tosatisfy 10a two-beam ..

작성자 최고관리자 작성일 2021-12-01
71

MRL [MRL] Prof. Chong Soo Lee:Enhancing low-cycle fatigue life of commercially-pure Ti by deformation at cryogenic temperature In this study, the low-cycle fatigue behavior of a cryogenic-rolled commercially pure titanium alloy was investigated, and compared with those of undeformed and room-temperature rolled ones. The amounts of deformation twins increased to >..

작성자 최고관리자 작성일 2021-11-11
70

MRL [MRL] Prof. Chong Soo Lee: Microstructural evolution and mechanical properties of nanocrystalline Fe–Mn–Al–C steel processed by high-pressure torsion In this study, microstructural evolution and mechanical properties of Fe–Mn–Al–C steel were investigated with the variation of shear strain imposed by high-pressure torsion (HPT). Two different initial grain sized steels were used..

작성자 최고관리자 작성일 2021-11-02
69

MRL [MRL] Prof. Chong Soo Lee: Effect of bainite fraction on hydrogen embrittlement of bainite/ martensite steel The paper quantifies how the fraction of bainite in dual-phase (bainite/martensite) steel affects its resistance to hydrogen embrittlement (HE). For this purpose, three steels that had different amounts (0, 0.9, and 1.8&..

작성자 최고관리자 작성일 2021-10-27
68

MCL [MCL] Prof. Nack Joon Kim:Improvement of strength – ductility balance of B2-strengthened lightweight steel The microstructure evolution and tensile properties of a newly designed Fe-21Mn-10Al-1C-5Ni (wt.%) lightweight steel subjected to two annealing conditions (inducing partial recrystallization and full recrystallization) and subsequent aging ..

작성자 최고관리자 작성일 2021-10-08
67

MCL [MCL] Prof. Nack Joon Kim: κ-Carbide assisted nucleation of B2: A novel pathway to develop high specific strength steels Controlling morphology of B2 phase as nano-sized particles that are homogenously distributed within austenite matrix has been remained as a challenging task particularly for hot rolled lightweight steels, where the nucleation sites for B2 p..

작성자 최고관리자 작성일 2021-10-08
66

EML [EML] Prof. Sung-Mo Jung: Effect of MgO on Phase Development in Hematite-ilmenite Ore Sinter The effect of MgO on phase development in a hematite-ilmenite ore sinter was investigated employing a vertical tube furnace by raising the temperature at 30 K/min to 1553 K. The phases developed after sintering were identified in terms of X..

작성자 최고관리자 작성일 2021-09-29
65

기타 POSTECH 철강에너지소재대학원, AI 활용 출강자동화 시스템 개발 용광로 쇳물의 온도는 1600℃~1700℃에 이른다. 그래서 제철 과정은 절대적 주의가 필요한 작업이다. 더군다나 출강은 용광로에서 불순물 제거 작업을 거친 쇳물을 이송 용기에 담는 공정인데, 베테랑의 숙련도와 집중력에 따라 조업의 품질에 절대적인 영향을 미친다. 이 위험천만한 고난도의 작업을 인공지능이 대신하면 어떨까? POSTECH(포항공과대학교, 총장 김무환) 철강∙에너지소재대학원 홍대근 교수와 임창희..

작성자 최고관리자 작성일 2021-09-02
64

CTL [CTL] Prof. Chang Hee Yim: The effect of Ni depletion on athermal martensitic transformation in 304 austenitic stainless steel Chemical and microstructural analyses were performed on Ni depletion zones in 304 austenitic stainless steelsheets after annealing and cooling with three different rates (0.2, 18.6, 160.0 ◦C/s). The analysis was focused onthe characteristic..

작성자 최고관리자 작성일 2021-08-26

SITE MAP

소개

사람들

연구분야

입시 및 교육

커뮤니티

커뮤니티

연구성과

검색